1. Litter-Robot 3 Troubleshooting: What Do The Lights Mean?
Red Light Flashing (Cat... · Litter-Robot 4: Light codes guide
Litter-Robot troubleshooting means learning about Litter-Robot lights: flashing blue light, flashing red light, blue and yellow lights, and more.
2. Litter-Robot 4: Red light bar flashing (Cat sensor fault)
If your unit has a flashing red light bar or the unit will not cycle, this indicates that the cat sensor has been triggered for more than 30 minutes.
Troubleshooting a flashing red light on your Litter-Robot 4? Visit our support page for effective solutions to cat sensor faults. Get help now!
3. Litter robot III red light flashing - RobotShop Community
Meer resultaten van community.robotshop.com
I purchased a new cat sensor and installed it but still didn’t fix the problem. I’ve unplugged it, turned off and on but it still is flashing red and globe won’t turn. Any suggestions?
4. Litter-Robot 4: Light codes guide
If your unit's light bar is flashing red, this indicates that a cat (or weight) has been detected for over 30 minutes. Learn more. Red momentary flash. If your ...
Discover solutions for all Litter-Robot 4 light codes in our comprehensive guide. Find quick fixes and get your Litter-Robot working perfectly again. Click now!
5. Green with Partial Red Flashing - Litter-Robot 4
If you see a green ping-pong sequence on the light bar, it means the three curtain sensors are attempting to auto-calibrate their cat detection levels. This ...
Learn to troubleshoot, clean, and calibrate OmniSense Sensors for peak Litter-Robot performance. View our troublshooting guide for help now!
6. Litter-Robot 4: Red light bar with partial white flashing (Globe position)
If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position during its previous cycle.
Visit for solutions if your Litter-Robot 4 has a red light bar with a partial white flashing globe. Get instant support and fixes today.
7. Red & Blue Alternating Light Bar Issue - Litter-Robot 4
Litter-Robot 4: Red and blue alternating light bar (OmniSense laser sensor fault) · Make sure your unit is plugged in. · Make sure your unit is connected and ...
See AlsoCraigslist El Dorado KansasEncounter a Laser Board Fault in your Litter-Robot 4? Navigate to our site for expert solutions on fixing red-blue-alternating-light-bar issues.
8. Litter-Robot 3: All three lights flashing (Globe position fault)
Red, then yellow, then blue (Flashing sequentially, one light at a time): This means the unit cannot find the Home position. It will continue to function in ...
Find solutions for your Litter-Robot 3's three lights flashing position sensors issue. Fix issues with your Connect Upgrade Kit today!
9. Litter Robot III - Flashing lights sequentially or flashing all at once
Most of you are here because there are 3 flashing lights on your Litter-Robot's control panel. Sometimes this problem is caused by a faulty power supply or ...
Most of you are here because there are 3 flashing lights on your Litter-Robot's control panel. Sometimes this problem is caused by a faulty power supply or the motor itself. If even after checking the set screw on the motor and checking the voltage on the power supply with a multimeter, the lights…
10. Litter-Robot 3 Ultimate Troubleshooting Guide
3 dec 2021 · LIGHTS ; RED FLASHING, Cat sensor fault. Faulty cat sensor. Check for too much litter; Press RESET ; YELLOW & BLUE SOLID. Sleep mode. Panel ...
The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. There's a lot of dust and debris which can cause issues, which leads to the robot not operating correctly. Customers often search online for a solution before contacting technical support, so this guide is intended to cover the most common situations.
11. Litter-Robot 4: Red with partial yellow flashing (Over-torque fault)
If your unit has a red light bar with partial yellow flashing, this indicates that the globe is most likely jammed or overloaded. You will also receive a ...
Get solutions for your Litter-Robot 4 red with partial yellow flashing over-torque fault. Find easy fixes here! Explore our support page now.
12. Litter Robot Troubleshooting: Fixing Common Litter-Robot 3 Issues
25 apr 2016 · This should activate the Cat Sensor. You will see the blue light going off and the red one going on instead – as a simulation of a cat entering ...
Need help with your Litter Robot 3 issues? These are the most common problems and step-by-step ways to fix them.
13. Red and green alternating light bar (Calibration issue) - Litter-Robot
If the unit displays a red and green alternating light bar, the unit has lost its factory scale calibration values. If your unit is displaying a red and green ...
Solve your Litter-Robot 4 red-green light issue with our easy guide. Get quick help for calibration issues. Click for immediate support!